Marshall Fey contact info

Have a generic question? Post it here.

If you have a question regarding a specific slot machine or trade stimulator please post it in either the Slot or Trade Stimulator area.

Marshall Fey contact info

Postby Rick-okc » Sat Aug 24, 2019 5:31 pm

Can someone please send me Marshall Fey's email or phone number?
I'd like to ask him some questions about a Fey revamp I have.

Rick
User avatar
Rick-okc
 
Posts: 328
Joined: Sun Nov 07, 2004 5:51 pm
Location: Shelbyville, TN

Re: Marshall Fey contact info

Postby BALTMANHD103 » Sat Aug 24, 2019 6:18 pm

You can find the info you need at www.livertybellsbook.com. or mfey@libertybellebooks.com
BALTMANHD103
 
Posts: 102
Joined: Wed Jul 17, 2019 6:08 pm
Location: Asheboro North Carolina

Re: Marshall Fey contact info

Postby MONTI » Sun Aug 25, 2019 7:12 am

Rick!
Please allow Marshall a couple of days to reply as he doesn't always answer his phone and usually takes a couple of days to reply when I call him!
What revamp are you curious about as Charles Fey was also a Pace Distributor back in the day and revamped some Early Pace slots!
Being here on the "LEFT" coast I have run across a few interesting Fey slots that I have talked to Marshall about!
The only one I have ever stumped him on that was Revamped buy Charles Fey was this Revamp below that had a "Lock" assembly on the lower front casting that he told me he had never seen before!

Ciao!
MONTI

1 Lock Area front.JPG


1 Lock Area inside.JPG
MONTI'S SLOT SHOP
BUY * SELL * TRADE * RESTORE
Over 50 years experience in slot restoration

Serving Northern California, Nevada & Beyond
User avatar
MONTI
 
Posts: 583
Joined: Sun Nov 07, 2010 6:35 pm
Location: NORTHERN CALIFORNIA

Re: Marshall Fey contact info

Postby nvmos2 » Sun Aug 25, 2019 1:09 pm

Very interesting revamp front.......what did it lock/unlock?
or is that what had you guys stumped?

Since it appears to be on a Jennings, maybe the lock was only used when the front was installed on a Mills or other model.
nvmos2
 
Posts: 808
Joined: Sat Jan 14, 2012 11:43 am
Location: SE Virginia

Re: Marshall Fey contact info

Postby MONTI » Sun Aug 25, 2019 1:53 pm

nvmos2 wrote:Very interesting revamp front.......what did it lock/unlock?
or is that what had you guys stumped?

Since it appears to be on a Jennings, maybe the lock was only used when the front was installed on a Mills or other model.



You are correct that is what stumped me while it was in the shop on the bench, I could not figure out what it was there for so I called Marshall after emailing him the photos and he didn't know either and had not seen that modification so it is still a mystery!
There is that extra hole in the base plate behind it! HMMMMMM?
As I've said before, whenever I think I have seen everything in 40 years of doing this something I have never seen before comes along but after talking to Marshall I told him I didn't feel so bad as he didn't know either! LOL
MONTI'S SLOT SHOP
BUY * SELL * TRADE * RESTORE
Over 50 years experience in slot restoration

Serving Northern California, Nevada & Beyond
User avatar
MONTI
 
Posts: 583
Joined: Sun Nov 07, 2010 6:35 pm
Location: NORTHERN CALIFORNIA

Re: Marshall Fey contact info

Postby Rick-okc » Sun Aug 25, 2019 6:24 pm

Thank you BALTMANHD103 for the contact info.
Thanks MONTI for the advice about Marshall getting back with me.
The machine I'm asking about is a Superior Confection Gold Award Bell I picked up a few months ago. It came out of the San Francisco area.
Story is it had been in a rec room since 1940. It was owned by a dentist in the San Francisco area. Not sure exactly where.

DSC_2633 low.jpg

DSC_2647 low.jpg
User avatar
Rick-okc
 
Posts: 328
Joined: Sun Nov 07, 2004 5:51 pm
Location: Shelbyville, TN

Re: Marshall Fey contact info

Postby MONTI » Sun Aug 25, 2019 7:02 pm

VERY NICE SLOT MACHINE Rick! =D>
Let us know what you find out!
Bona Fortuna!
MONTI
MONTI'S SLOT SHOP
BUY * SELL * TRADE * RESTORE
Over 50 years experience in slot restoration

Serving Northern California, Nevada & Beyond
User avatar
MONTI
 
Posts: 583
Joined: Sun Nov 07, 2010 6:35 pm
Location: NORTHERN CALIFORNIA

Re: Marshall Fey contact info

Postby RameGoom » Sun Aug 25, 2019 8:22 pm

I have a revamp with that lock and cover on the front. If I remove the cover, it accesses a lever that releases the back door. I believe it's a secondary lock bar for the door, but there is a part missing on the pictured machine.
Slowly building a knowledge base on E2000 series Bally machines and J400 Jennings. Started with the antique Mills and Jennings. Getting there...
User avatar
RameGoom
 
Posts: 354
Joined: Wed Dec 06, 2006 4:47 pm
Location: Loveland, CO

Re: Marshall Fey contact info

Postby RameGoom » Sun Aug 25, 2019 8:36 pm

pace-dual-jackpot-revamp-front.jpg


backdoor-release-lever.jpg


finger-actuator.jpg
Slowly building a knowledge base on E2000 series Bally machines and J400 Jennings. Started with the antique Mills and Jennings. Getting there...
User avatar
RameGoom
 
Posts: 354
Joined: Wed Dec 06, 2006 4:47 pm
Location: Loveland, CO

Re: Marshall Fey contact info

Postby MONTI » Mon Aug 26, 2019 7:50 am

RameGoom wrote:I have a revamp with that lock and cover on the front. If I remove the cover, it accesses a lever that releases the back door. I believe it's a secondary lock bar for the door, but there is a part missing on the pictured machine.


Interesting as that may be the answer I've been looking for!
Does the 2nd hole in the base plate as shown here below allow for the passage and operation of the back door release?
Would it be possible to see an internal view of the back door release assembly so I could add it to my files?
Just a quick question as I don't want to interfere here on Rick's post!
MONTI

Hole in base plate.jpg
MONTI'S SLOT SHOP
BUY * SELL * TRADE * RESTORE
Over 50 years experience in slot restoration

Serving Northern California, Nevada & Beyond
User avatar
MONTI
 
Posts: 583
Joined: Sun Nov 07, 2010 6:35 pm
Location: NORTHERN CALIFORNIA

Next

Return to Just Chatting

Who is online

Users browsing this forum: Google [Bot] and 29 guests

cron